000-00000-000-02-A Halogen Light Source with RS232 Intensity Control HL-2000-HP-232 Installation and Operation Manual Document Number 000-1000
1: Setup 2 000-10000-140-02-201307 2. Inspect the outside of the instrument and make sure that there is no damage. Do not use the instrument if da
1: Setup 000-10000-140-02-201307 3 ► Procedure 1. Plug the power supply into a wall outlet. 2. Plug the other end of the power supply cable into
1: Setup 4 000-10000-140-02-201307
000-10000-140-02-201307 5 Chapter 2 Operation Optimizing the Optical Power Output The HL-2000-HP-232 is adjusted at the factory to provide maximum p
2: Operation 6 000-10000-140-02-201307 3. Shift the SMA socket to optimize the optical power of the light source. 4. Tighten the blocking screw t
000-10000-140-02-201307 7 Chapter 3 Bulb Replacement Overview To order replacement bulbs for the HL-2000-HP-232, consult the Parts List. WARNING
3: Bulb Replacement 8 000-10000-140-02-201307 4. Loosen the hex screw on the lamp housing. 5. Remove the bulb by pulling it back away from the c
000-10000-140-02-201307 9 Appendix A ASCII Commands In serial communications mode, the motion controller is controlled via a series of ASCII instruc
A: ASCII Commands 10 000-10000-140-02-201307 Command Function Description Example DI Disable Drive Execution of this command disables the driv
A: ASCII Commands 000-10000-140-02-201307 11 Command Function Description Example DCE Delayed Current Error This command sets the delay betwee
Copyright © 2009 Ocean Optics, Inc. All rights reserved. No part of this publication ma
A: ASCII Commands 12 000-10000-140-02-201307 Command Function Description Example HL Home Limit Action This command is used to set the action
A: ASCII Commands 000-10000-140-02-201307 13 Command Function Description Example GRC Get Real Current This command returns the current being
A: ASCII Commands 14 000-10000-140-02-201307 Command Function Description Example VER Get Version This command returns firmware version. VER
000-10000-140-02-201307 15 Appendix B HL-2000-HP-232 Specifications This section provides information on the operating environment, physical control
B: HL-2000-HP-232 Specifications 16 000-10000-140-02-201307 Parts List Spare Parts / Order Information Item Number Halogen high-power 20 W light s
000-10000-140-02-201307 17 Index A ASCII commands, 9 B bulb replacement, 7 C commands configuration-related, 10 data-returning, 12 external switch l
Index 18 000-10000-140-02-201307
000-10000-140-02-201307 A Important Safety Notices 1. Read all safety and operating instructions before using this equipment. 2. Use this equipm
Important Safety Notices B 000-10000-140-02-201307
000-10000-140-02-201307 i Table of Contents About This Manual ...
Table of Contents ii 000-10000-140-02-201307 Appendix B: HL-2000-HP-232 Specifications ... 15 Specifications ...
000-10000-140-02-201307 iii About This Manual Document Purpose and Intended Audience This document provides you with set-up and operation informat
About This Manual iv 000-10000-140-02-201307 Upgrades Occasionally, you may find that you need Ocean Optics to make a change or an upgrade to your
000-10000-140-02-201307 1 Chapter 1 Setup Overview The high-power Halogen Light Source with attenuator and shutter uses a 20-watt bulb for applica
Comments to this Manuals